Appendix

Data Message Example

Example data message:

{
  "ts": 1608416763.9,
  "ambient": 25.83,
  "current1": 0.16,
  "angle": 1.7,
  "pitch": -0.9,
  "motion": 24,
  "wifi_ip": "192.168.1.178",
  "deviceid": "BD6AEDJQ2",
  "vreg": 8.98,
  "vsys": 4.09,
  "vbat": 0,
  "wifi_rssi": -32,
  "light": 1,
  "accel_x": 0.02,
  "accel_y": -0.03,
  "accel_z": -1.01,
  "events": [
    {
      "msg": "Low",
      "topic": "pitch",
      "lv": 30
    }
  ],
  "pressure": 101.26,
  "vin": 12.11,
  "analog1": 0,
  "roll": -1.5,
  "can1": [
    {
      "data": "42C8590803FFD908",
      "id": 419371762
    },
    {
      "data": "4DE9BD3404AA7D34",
      "id": 419372018
    }
  ]
}

List of Data Keys

Key	Description	Units
vsys	Internal system voltage	Volts
vin	Input supply voltage	Volts
vbat	AA Battery Voltage	Volts
tamper	Light sensor tamper status (0 or 1)
gps_lat	GPS Latitude
gps_lon	GPS Longitude
gps_speed	GPS Speed	km/h
ambient	Ambient Temperature	degrees C
capture1	Serial 1 Capture
pitch	Pitch of device	degrees
roll	Roll of device	degrees
angle	Angle of device	degrees
motion	Motion/Vibration	millig-g
analog1	Analog Input 1
analog2	Analog Input 2
analog3	Analog Input 3
analog4	Analog Input 4
analog5	Analog Input 5
digital1	Digital Input 1
digital2	Digital Input 2
digital3	Digital Input 3
digital4	Digital Input 4
digital5	Digital Input 5
tc1	Thermocouple Input 1	degrees C
freq1	Frequency Input 1	Hz
duty1	Duty Cycle Input 1	%
pulse1	Pulse Count Input 1
current1	Current Loop Input 1
current2	Current Loop Input 2
mod1	Modbus Channel 1
mod2	Modbus Channel 2
mod3	Modbus Channel 3
mod4	Modbus Channel 4
mod5	Modbus Channel 5
mod6	Modbus Channel 6
mod7	Modbus Channel 7
mod8	Modbus Channel 8
mod9	Modbus Channel 9
mod10	Modbus Channel 10
can1	CANbus Channel 1
can2	CANbus Channel 2
state	Current device state (0 to 6)
state1_hrs	Number of hours in device state 1
state2_hrs	Number of hours in device state 2
state3_hrs	Number of hours in device state 3
state4_hrs	Number of hours in device state 4
state5_hrs	Number of hours in device state 5
state6_hrs	Number of hours in device state 6
gsm_iccid	ICCID of SIM card
gsm_imei	IMEI of device
gsm_carrier	The mobile carrier

List of Configuration Keys

Type	Key	Name	Description	Range	Units	Notes
string	device.id	Device ID	Unique device serial number.			readonly
string	device.model	Device Model	The device model number.			readonly
string	device.fw	Firmware Version	The device firmware revision.			readonly
string	device.hw	Hardware Revision	The device hardware revision.			readonly
string	device.name	Device Name	A name for the device that is meaningful to the user.
integer	device.base_interval	Base Interval	The time after which the device will wakeup to check which measurements need to be taken and if a transmission is scheduled.	1 to 86400	Seconds
integer	device.transmit_interval	Transmit Interval	The number of base intervals after which a transmission is made.	1 to 1000
integer	device.exception_interval	Exception Interval	If a warning or alarm is active, this setting overrides the Transmit Interval, allowing an increased rate of transmission.	1 to 1000
boolean	device.always_on	Device Always On	If enabled the device will not sleep between Base Intervals and will remain awake. Not recommended for battery powered applications.
boolean	device.batch_tx_enable	Batch Transmit	If enabled, all measurements at the Base Interval will be stored and transmitted at the Transmit Interval. Useful for low power optimisation.
boolean	device.web_always_on	Web Server	This setting will keep the device webserver on all the time (while device is awake). Normally the websever is only available in setup mode.
boolean	device.vin.alert_enable	Power Loss Alert	Sends and alert when voltage on the power input is below a fixed threshold.
boolean	device.vin.sleep_enable	Hibernate on Power Loss	Puts the device into a low power state, when the power input is below a fixed threshold. The device will run off it’s internal backup battery and report periodically.
integer	device.vin.sleep_delay	Hibernate Delay Intervals	The number of base intervals to wait after power loss before entering hibernate mode.	0 to 1000
boolean	device.vin.count_hours	Count Hours	Counts the number of hours the power input is active. Typically used as an engine hour meter when powered from ignition.
boolean	device.batt.alert_enable	AA Battery Low Alert	Enable if an alert is to be sent when the AA battery level drops below a specified limit.
decimal	device.batt.threshold	Threshold	The lower threshold at which an alert is raised.		Volts
boolean	wifi.sta.enable	Wifi	Connect to existing Wifi connection specified below.
string	wifi.sta.ssid	SSID	Wifi SSID to connect to.
password	wifi.sta.pass	Password	Wifi password to use for connection.
string	wifi.sta.ip	Static IP Address	Leave blank if assigned by DHCP.
string	wifi.sta.netmask	Static Netmask	Leave blank if assigned by DHCP.
string	wifi.sta.gw	Static Gateway	Leave blank if assigned by DHCP.
string	wifi.sta.nameserver	DNS Server	Leave blank if assigned by DHCP.
boolean	gsm.enable	4G LTE	Enable the 4G LTE connection.
string	gsm.apn	APN	Access Point Name of mobile operator
string	gsm.user	Username	Username for data connection. Leave blank if not specified
string	gsm.pass	Password	Password for data connection. Leave blank if not specified
string	tamper.name	Name	A name for the light sensor that is meaningful to the user.
boolean	tamper.enable	Tamper Alert	This parameter determines if an alert is generated when the light sensor detects light or not.
string	ambient.name	Name	A name for the input that is meaningful to the user.
integer	ambient.interval	Interval	The number of base intervals after which the temperature is sampled. A value of 1 means that the input is collected every base interval. Set to 0 to disable.	0 to 10000
decimal	ambient.hysteresis	Hysteresis	The amount by which the measured value has to drop below the threshold to re-enable the alert after an event.	0 to 100	°C
string	ambient.warning	Warning	Warning thresholds. Refer to user guide.	-40 to 100	°C
string	ambient.alarm	Alarm	Alarm thresholds. Refer to user guide.	-40 to 100	°C
string	accel.name	Name	A name for the input that is meaningful to the user.
integer	accel.interval	Interval	The number of base intervals after which the accelerometer is sampled. A value of 1 means that the input is collected every base interval. Set to 0 to disable.	0 to 10000
boolean	accel.outputxyz	Output XYZ Vectors	Send X,Y,Z gravity vectors in data output.
decimal	accel.hysteresis	Hysteresis	The amount by which the pitch, roll or angle has to exceed a threshold before triggering alarms or warnings.	0 to 20	Degrees
string	accel.pitch.warning	Pitch Warning	Warning thresholds. Refer to user guide.	-90 to 90	Degrees
string	accel.pitch.alarm	Pitch Alarm	Alarm thresholds. Refer to user guide.	-90 to 90	Degrees
string	accel.roll.warning	Roll Warning	Warning thresholds. Refer to user guide.	-90 to 90	Degrees
string	accel.roll.alarm	Roll Alarm	Alarm thresholds. Refer to user guide.	-90 to 90	Degrees
string	accel.angle.warning	Angle Warning	Warning thresholds. Refer to user guide.	0 to 90	Degrees
string	accel.angle.alarm	Angle Alarm	Alarm thresholds. Refer to user guide.	0 to 90	Degrees
string	accel.motion.warning	Vibration Warning	Warning thresholds. Refer to user guide.	0 to 5000	milli-g
string	accel.motion.alarm	Vibration Alarm	Alarm thresholds. Refer to user guide.	0 to 5000	milli-g
boolean	accel.motion.wake_from_hibernate	Wake from Hibernate	The high warning vibration threshold is used to wake the device when hibernating.
decimal	accel.motion.wake_threshold	Vibration Wake Threshold	The vibration threshold above which the device will wake from hibernation.	1 to 2000	milli-g
boolean	accel.motion.count_hours	Count Vibration Hours	Counts the number of hours the device exceeds the Vibration Wake Threshold. Typically used as an machinery work vs idle hour meter.
string	ble.name	Name	A name that is meaningful to the user.
string	ble.addr	Address	The Bluetooth Address of this device.			readonly
integer	ble.interval	Interval	The number of base intervals at which the Bluetooth module is turned on. Set to 0 to disable.	0 to 10000
integer	ble.scan_time	Scan Time	How long to scan for Bluetooth advertisements each interval.	1 to 300	Seconds
string	ble.id_list	Address Capture List	List of addresses to be captured in HEX format, separated by a comma eg: AC233F6925AD. Leave blank to capture all.
boolean	ble.send_data	Send Raw Data	Send all captured data in the standard data message. If unticked, data is only delivered to the scripting handler.
string	gps.name	Name	A name for the GPS signal that is meaningful to the user.
integer	gps.interval	Interval	The number of base intervals after which the gps is sampled. A value of 1 means that the input is collected every base interval. Set to 0 to disable.	0 to 10000
integer	gps.maxtime	Max Time	Maximum time the device will wait for a valid GPS fix.	0 to 3600	Seconds
boolean	gps.position.alert.enable	Position Alert	Sets whether a change in position generates an alert.
integer	gps.position.alert.radius	Radius	An alert will be raised if the device moves further than this value from the expected position.	1 to 10000	Meters
integer	gps.position.alert.hysteresis	Hysteresis	Once the alert is active or inactive, the radius must change by this value to change the alert state.	1 to 10000	Meters
decimal	gps.position.alert.lat	Expected Latitude	Latitude at which the device is expected to be.	-90 to 90	Degrees
decimal	gps.position.alert.lon	Expected Longitude	Longitude at which the device is expected to be.	-180 to 180	Degrees
boolean	gps.speed.count_hours	Count Movement Hours	Counts the number of hours the device is moving according to the GPS speed.
boolean	gps.speed.alert.enable	Speed Alert	Sets whether a change in speed generates an alert.
integer	gps.speed.alert.threshold	Threshold	An alert will be raised if the device’s speed goes above this threshold.	1 to 1000	km/h
integer	gps.speed.alert.hysteresis	Hysteresis	Once the alert is active or inactive, the speed must change by this value to change the alert state.	1 to 1000	km/h
string	input1.name	Name	A name for the input that is meaningful to the user.
integer	input1.interval	Interval	The number of base intervals after which the input is sampled. A value of 1 means that the input is collected every base interval. Set to 0 to disable.	0 to 10000
preset	input1.mode	Mode	Specifies the function of the IN1 terminal. The calibration, warnings and alarms are applied to this mode.			Digital,Analog,Frequency,Duty Cycle
decimal	input1.digital.threshold	Digital Threshold	A threshold against which the input is compared to determine if the input state is ON or OFF.	0 to 30	Volts
decimal	input1.digital.hysteresis	Digital Hysteresis	Once the input is in a certain state, hysteresis is the amount by which the input has to change before moving to the other state.	0 to 20	Volts
boolean	input1.digital.count_hours	Count Hours	Counts the number of hours the digtial input is ON (above threshold).
boolean	input1.digital.alert.enable	Digital Change Alert	Sets whether a change in digital state generates an alert.
string	input1.cal	Analog 1 Calibration	Calibration parameters for Analog 1. Refer to user guide.
string	input1.unit	Unit	The unit of measure associated with the calibration. Eg: Litres, RPM
string	input1.warning	Warning	Warning thresholds. Refer to user guide.
string	input1.alarm	Alarm	Alarm thresholds. Refer to user guide.
decimal	input1.hysteresis	Alarm/Warning Hysteresis	Once the input is in a certain state, hysteresis is the amount by which the input has to change before moving to the other state.
boolean	input1.pulse.enable	Pulse Counting	Enables counting of pulses in addition to frequency measurement.
integer	input1.pulse.reset_value	Reset Value	The value at which the number of pulses counted on the input is reset to zero.	1 to 2000000000	Counts
decimal	input1.pulse.scaling	Pulse Scaling	Multiplier to convert the pulse count to a useful unit.
string	input1.pulse.unit	Pulse Unit	The unit of measure associated with the scaled pulse count. Eg: Litres
string	input1.pulse.warning	Pulse Warning	Warning thresholds. Refer to user guide.
string	input1.pulse.alarm	Pulse Alarm	Alarm thresholds. Refer to user guide.
string	input2.name	Name	A name for the input that is meaningful to the user.
integer	input2.interval	Interval	The number of base intervals after which the input is sampled. A value of 1 means that the input is collected every base interval. Set to 0 to disable.	0 to 10000
preset	input2.mode	Mode	Specifies the function of the IN2 terminal. The calibration, warnings and alarms are applied to this mode.			Digital,Analog
decimal	input2.digital.threshold	Digital Threshold	A threshold against which the input is compared to determine if the input state is ON or OFF.	0 to 30	Volts
decimal	input2.digital.hysteresis	Digital Hysteresis	Once the input is in a certain state, hysteresis is the amount by which the input has to change before moving to the other state.	0 to 20	Volts
boolean	input2.digital.count_hours	Count Hours	Counts the number of hours the digtial input is ON (above threshold).
boolean	input2.digital.alert.enable	Digital Change Alert	Sets whether a change in digital state generates an alert.
string	input2.cal	Analog 2 Calibration	Calibration parameters for Analog 2. Refer to user guide.
string	input2.unit	Unit	The unit of measure associated with the calibration. Eg: Litres, RPM, Volts
string	input2.warning	Warning	Warning thresholds. Refer to user guide.
string	input2.alarm	Alarm	Alarm thresholds. Refer to user guide.
decimal	input2.hysteresis	Alarm/Warning Hysteresis	Once the input is in a certain state, hysteresis is the amount by which the input has to change before moving to the other state.
string	output1.name	Name	A name for the input that is meaningful to the user.
integer	output1.interval	Interval	Does not affect output mode. The number of base intervals at which the input is sampled. Set to 0 to disable. Set to 1 for every base interval.	0 to 10000
preset	output1.mode	Mode	Specifies the function of the OUT1 terminal.			Output,Digital,Analog
boolean	output1.warnings	Warnings	Determines if the output is turned on when a warning is active.
boolean	output1.alarms	Alarms	Determines if the output is turned on when an alarm is active.
boolean	output1.alerts	Alerts	Determines if the output is turned on when an alert is active.
integer	output1.hold_time	Hold Time	Sets the time in seconds for which the output is held on after it is triggered. If set to zero, the output remains on while any exceptions are active.		Seconds
boolean	output1.digital.alert.enable	Digital Change Alert	If enabled, a change in digital state will generate an alert.
string	output1.cal	Analog 3 Calibration	Calibration parameters for Analog 3. Refer to user guide.
string	output1.unit	Unit	The unit of measure associated with the calibration. Examples: Litres, RPM, Volts
string	output1.warning	Warning	Warning thresholds. Refer to user guide.
string	output1.alarm	Alarm	Alarm thresholds. Refer to user guide.
decimal	output1.hysteresis	Alarm/Warning Hysteresis	Once the input is in a certain state, hysteresis is the amount by which the input has to change before moving to the other state.
string	tc1.name	Name	A name for the input that is meaningful to the user.
integer	tc1.interval	Interval	The number of base intervals after which the thermocouple is measured and events are checked. A value of 1 means that the input is collected every base interval. Set to 0 to disable.	0 to 10000
decimal	tc1.hysteresis	Hysteresis	The amount by which the measured value has to drop below the threshold to re-enable the event.	-1000 to 1000	°C
string	tc1.type	Type	Determines the type of thermocouple connected. Valid values are: K, J, T, N, S, E, B and R
string	tc1.warning	Warning	Warning thresholds. Refer to user guide.	-1000 to 1000	°C
string	tc1.alarm	Alarm	Alarm thresholds. Refer to user guide.	-1000 to 1000	°C
string	can1.name	Name	A name that is meaningful to the user.
integer	can1.interval	Interval	The number of base intervals after which the CAN module is turned on. Set to 0 to disable.	0 to 10000
integer	can1.nominal_baud	Nominal Baud Rate	Baud rate for CAN communication. Supported values are: 125, 250, 500, 1000		kbit/s
integer	can1.capture_time	Capture Time	The device will capture matching messages for this length of time.		Seconds
boolean	can1.tx_enable	TX Enable	Allows the device to transmit and acknowledge messages on the CAN bus.
string	can1.id_list	ID Capture List	List of IDs to be captured in HEX format, separated by a comma eg: 18FEE60A. Leave blank to capture all.
boolean	can1.send_data	Send Raw Data	Send all captured data in the standard data message. If unticked, data is only delivered to the scripting handler.
string	can2.name	Name	A name that is meaningful to the user.
integer	can2.interval	Interval	The number of base intervals after which the CAN module is turned on. Set to 0 to disable.	0 to 10000
integer	can2.nominal_baud	Nominal Baud Rate	Baud rate for CAN communication. Supported values are: 125, 250, 500, 1000		kbit/s
integer	can2.capture_time	Capture Time	The device will capture matching messages for this length of time.		Seconds
boolean	can2.tx_enable	TX Enable	Allows the device to transmit and acknowledge messages on the CAN bus.
string	can2.id_list	ID Capture List	List of IDs to be captured in HEX format, separated by a comma eg: 18FEE60A. Leave blank to capture all.
boolean	can2.send_data	Send Raw Data	Send all captured data in the standard data message. If unticked, data is only delivered to the scripting handler.
string	current1.name	Name	A name for the input that is meaningful to the user.
integer	current1.interval	Interval	The number of base intervals after which the input is sampled. A value of 1 means that the input is collected every base interval. Set to 0 to disable.	0 to 10000
preset	current1.mode	Mode	Specifies the function of the SRC1 terminal.			Current,Digital
boolean	current1.always_on	Always On	Determines if Switched Power is to be enabled permanently.
decimal	current1.start_time	Start Time	Time in seconds that the output is turned on before measurements are taken. Allows an external device to stabilise.	0 to 3600	Seconds
boolean	current1.digital.alert.enable	Digital Change Alert	Sets whether a change in digital state generates an alert. (Digital Mode Only)
string	current1.cal	Current 1 Calibration	Calibration parameters for Current 1. Refer to user guide.
string	current1.unit	Unit	The unit of measure associated with the calibration. Eg: Percent, Litres
string	current1.warning	Warning	Warning thresholds. Refer to user guide.
string	current1.alarm	Alarm	Alarm thresholds. Refer to user guide.
decimal	current1.hysteresis	Alarm/Warning Hysteresis	The amount by which the calibrated current value has to drop below the threshold to re-enable the event.
string	current2.name	Name	A name for the input that is meaningful to the user.
integer	current2.interval	Interval	The number of base intervals after which the input is sampled. A value of 1 means that the input is collected every base interval. Set to 0 to disable.	0 to 10000
preset	current2.mode	Mode	Specifies the function of the SRC2 terminal.			Current,Digital
boolean	current2.always_on	Always On	Determines if Switched Power is to be enabled permanently.
decimal	current2.start_time	Start Time	Time in seconds that the output is turned on before measurements are taken. Allows an external device to stabilise.	0 to 3600	Seconds
boolean	current2.digital.alert.enable	Digital Change Alert	Sets whether a change in digital state generates an alert. (Digital Mode Only)
string	current2.cal	Current 2 Calibration	Calibration parameters for Current 2. Refer to user guide.
string	current2.unit	Unit	The unit of measure associated with the calibration. Eg: Percent, Litres
string	current2.warning	Warning	Warning thresholds. Refer to user guide.
string	current2.alarm	Alarm	Alarm thresholds. Refer to user guide.
decimal	current2.hysteresis	Alarm/Warning Hysteresis	The amount by which the calibrated current value has to drop below the threshold to re-enable the event.
string	serial1.name	Name	A name for the input that is meaningful to the user.
integer	serial1.interval	Interval	The number of base intervals after which the serial port is turned on. Set to 0 to disable.	0 to 10000
preset	serial1.type	Type	The electrical interface type.			RS232,RS485
boolean	serial1.termination	Termination Resistor	This parameter enables the integrated termination resistor.
preset	serial1.mode	Mode	Describes how the serial port is to be handled. CAPTURE: serial data is captured between start and end characters. MODBUS: serial data is treated according to MODBUS RTU standard			Capture,Modbus,Scripted
integer	serial1.baud	Baud Rate	Baud rate for serial communication. Common values are: 4800, 9600, 19200, 38400, 57600, 115200
string	serial1.settings	Settings	A string describing the number of bytes: 7,8,9. Parity type: N(none), E(even), O(odd). Number of stop bits: 1 or 2. Typically: 8N1
string	serial1.capture.start	Start String	The serial port starts reading data when it detects these characters. Example: $GPGGA, serial data will be ignored until $GPGGA is received after which data will be captured. If nothing is specified, the serial port will capture all data until the timeout period is reached.
integer	serial1.capture.start_idle_time	Idle Time Before Start	For a valid start condition, there must be this amount of idle time before receiving serial data. Additionally, the captured data will restarted if the serial port is idle for this time. Set to 0 to disable.	0 to 60000	Milliseconds
string	serial1.capture.end	End String	Once capturing, if these characters are received, the serial port will stop capturing and will return to sleep. For binary data or escape sequences refer to the User Guide.
string	serial1.capture.request	Request String	This string will be sent when the serial port is first turned on. Use this function to request data from a remote module.
integer	serial1.capture.maxtime	Max Time	The device will wait this length of time for a valid capture.		Seconds
integer	serial1.capture.maxchars	Max Chars	Maximum number of characters to be captured before the serial port goes back to sleep.
boolean	serial1.capture.alert	Alert on Capture	If checked an alert will be raised on any successful serial capture.
decimal	serial1.modbus.timeout	Slave Timeout	How long to wait for a response from each slave device.	0 to 10	Seconds
string	mod1.name	Modbus 1 Name	A meaningful name for the measurement.
string	mod1.settings	Modbus 1 Settings	Settings for Modbus Channel 1. Refer to user guide.
string	mod1.cal	Modbus 1 Calibration	Calibration paramters for Modbus Channel 1. Refer to user guide.
string	mod1.unit	Modbus 1 Unit	The unit of measure associated with the calibration.
string	mod1.warning	Warning	Warning thresholds. Refer to user guide.
string	mod1.alarm	Alarm	Alarm thresholds. Refer to user guide.
string	mod2.name	Modbus 2 Name	A meaningful name for the measurement.
string	mod2.settings	Modbus 2 Settings	Settings for Modbus Channel 2. Refer to user guide.
string	mod2.cal	Modbus 2 Calibration	Calibration paramters for Modbus Channel 2. Refer to user guide.
string	mod2.unit	Modbus 2 Unit	The unit of measure associated with the calibration.
string	mod2.warning	Warning	Warning thresholds. Refer to user guide.
string	mod2.alarm	Alarm	Alarm thresholds. Refer to user guide.
string	mod3.name	Modbus 3 Name	A meaningful name for the measurement.
string	mod3.settings	Modbus 3 Settings	Settings for Modbus Channel 3. Refer to user guide.
string	mod3.cal	Modbus 3 Calibration	Calibration paramters for Modbus Channel 3. Refer to user guide.
string	mod3.unit	Modbus 3 Unit	The unit of measure associated with the calibration.
string	mod3.warning	Warning	Warning thresholds. Refer to user guide.
string	mod3.alarm	Alarm	Alarm thresholds. Refer to user guide.
string	mod4.name	Modbus 4 Name	A meaningful name for the measurement.
string	mod4.settings	Modbus 4 Settings	Settings for Modbus Channel 4. Refer to user guide.
string	mod4.cal	Modbus 4 Calibration	Calibration paramters for Modbus Channel 4. Refer to user guide.
string	mod4.unit	Modbus 4 Unit	The unit of measure associated with the calibration.
string	mod4.warning	Warning	Warning thresholds. Refer to user guide.
string	mod4.alarm	Alarm	Alarm thresholds. Refer to user guide.
string	mod5.name	Modbus 5 Name	A meaningful name for the measurement.
string	mod5.settings	Modbus 5 Settings	Settings for Modbus Channel 5. Refer to user guide.
string	mod5.cal	Modbus 5 Calibration	Calibration paramters for Modbus Channel 5. Refer to user guide.
string	mod5.unit	Modbus 5 Unit	The unit of measure associated with the calibration.
string	mod5.warning	Warning	Warning thresholds. Refer to user guide.
string	mod5.alarm	Alarm	Alarm thresholds. Refer to user guide.
string	mod6.name	Modbus 6 Name	A meaningful name for Modbus Channel 6.
string	mod6.settings	Modbus 6 Settings	Settings for Modbus Channel 6. Refer to user guide.
string	mod6.cal	Modbus 6 Calibration	Calibration paramters for Modbus Channel 6. Refer to user guide.
string	mod6.unit	Modbus 6 Unit	The unit of measure associated with the calibration.
string	mod6.warning	Warning	Warning thresholds. Refer to user guide.
string	mod6.alarm	Alarm	Alarm thresholds. Refer to user guide.
string	mod7.name	Modbus 7 Name	A meaningful name for the measurement.
string	mod7.settings	Modbus 7 Settings	Settings for Modbus Channel 7. Refer to user guide.
string	mod7.cal	Modbus 7 Calibration	Calibration paramters for Modbus Channel 7. Refer to user guide.
string	mod7.unit	Modbus 7 Unit	The unit of measure associated with the calibration.
string	mod7.warning	Warning	Warning thresholds. Refer to user guide.
string	mod7.alarm	Alarm	Alarm thresholds. Refer to user guide.
string	mod8.name	Modbus 8 Name	A meaningful name for the measurement.
string	mod8.settings	Modbus 8 Settings	Settings for Modbus Channel 8. Refer to user guide.
string	mod8.cal	Modbus 8 Calibration	Calibration paramters for Modbus Channel 8. Refer to user guide.
string	mod8.unit	Modbus 8 Unit	The unit of measure associated with the calibration.
string	mod8.warning	Warning	Warning thresholds. Refer to user guide.
string	mod8.alarm	Alarm	Alarm thresholds. Refer to user guide.
string	mod9.name	Modbus 9 Name	A meaningful name for the measurement.
string	mod9.settings	Modbus 9 Settings	Settings for Modbus Channel 9. Refer to user guide.
string	mod9.cal	Modbus 9 Calibration	Calibration paramters for Modbus Channel 9. Refer to user guide.
string	mod9.unit	Modbus 9 Unit	The unit of measure associated with the calibration.
string	mod9.warning	Warning	Warning thresholds. Refer to user guide.
string	mod9.alarm	Alarm	Alarm thresholds. Refer to user guide.
string	mod10.name	Modbus 10 Name	A meaningful name for the measurement.
string	mod10.settings	Modbus 10 Settings	Settings for Modbus Channel 10. Refer to user guide.
string	mod10.cal	Modbus 10 Calibration	Calibration paramters for Modbus Channel 10. Refer to user guide.
string	mod10.unit	Modbus 10 Unit	The unit of measure associated with the calibration.
string	mod10.warning	Warning	Warning thresholds. Refer to user guide.
string	mod10.alarm	Alarm	Alarm thresholds. Refer to user guide.
string	mod11.name	Modbus 11 Name	A meaningful name for the measurement.
string	mod11.settings	Modbus 11 Settings	Settings for Modbus Channel 11. Refer to user guide.
string	mod11.cal	Modbus 11 Calibration	Calibration paramters for Modbus Channel 11. Refer to user guide.
string	mod11.unit	Modbus 11 Unit	The unit of measure associated with the calibration.
string	mod11.warning	Warning	Warning thresholds. Refer to user guide.
string	mod11.alarm	Alarm	Alarm thresholds. Refer to user guide.
string	mod12.name	Modbus 12 Name	A meaningful name for the measurement.
string	mod12.settings	Modbus 12 Settings	Settings for Modbus Channel 12. Refer to user guide.
string	mod12.cal	Modbus 12 Calibration	Calibration paramters for Modbus Channel 12. Refer to user guide.
string	mod12.unit	Modbus 12 Unit	The unit of measure associated with the calibration.
string	mod12.warning	Warning	Warning thresholds. Refer to user guide.
string	mod12.alarm	Alarm	Alarm thresholds. Refer to user guide.
string	mod13.name	Modbus 13 Name	A meaningful name for the measurement.
string	mod13.settings	Modbus 13 Settings	Settings for Modbus Channel 13. Refer to user guide.
string	mod13.cal	Modbus 13 Calibration	Calibration paramters for Modbus Channel 13. Refer to user guide.
string	mod13.unit	Modbus 13 Unit	The unit of measure associated with the calibration.
string	mod13.warning	Warning	Warning thresholds. Refer to user guide.
string	mod13.alarm	Alarm	Alarm thresholds. Refer to user guide.
string	mod14.name	Modbus 14 Name	A meaningful name for the measurement.
string	mod14.settings	Modbus 14 Settings	Settings for Modbus Channel 14. Refer to user guide.
string	mod14.cal	Modbus 14 Calibration	Calibration paramters for Modbus Channel 14. Refer to user guide.
string	mod14.unit	Modbus 14 Unit	The unit of measure associated with the calibration.
string	mod14.warning	Warning	Warning thresholds. Refer to user guide.
string	mod14.alarm	Alarm	Alarm thresholds. Refer to user guide.
string	mod15.name	Modbus 15 Name	A meaningful name for the measurement.
string	mod15.settings	Modbus 15 Settings	Settings for Modbus Channel 15. Refer to user guide.
string	mod15.cal	Modbus 15 Calibration	Calibration paramters for Modbus Channel 15. Refer to user guide.
string	mod15.unit	Modbus 15 Unit	The unit of measure associated with the calibration.
string	mod15.warning	Warning	Warning thresholds. Refer to user guide.
string	mod15.alarm	Alarm	Alarm thresholds. Refer to user guide.
string	mod16.name	Modbus 16 Name	A meaningful name for Modbus Channel 16.
string	mod16.settings	Modbus 16 Settings	Settings for Modbus Channel 16. Refer to user guide.
string	mod16.cal	Modbus 16 Calibration	Calibration paramters for Modbus Channel 16. Refer to user guide.
string	mod16.unit	Modbus 16 Unit	The unit of measure associated with the calibration.
string	mod16.warning	Warning	Warning thresholds. Refer to user guide.
string	mod16.alarm	Alarm	Alarm thresholds. Refer to user guide.
string	mod17.name	Modbus 17 Name	A meaningful name for the measurement.
string	mod17.settings	Modbus 17 Settings	Settings for Modbus Channel 17. Refer to user guide.
string	mod17.cal	Modbus 17 Calibration	Calibration paramters for Modbus Channel 17. Refer to user guide.
string	mod17.unit	Modbus 17 Unit	The unit of measure associated with the calibration.
string	mod17.warning	Warning	Warning thresholds. Refer to user guide.
string	mod17.alarm	Alarm	Alarm thresholds. Refer to user guide.
string	mod18.name	Modbus 18 Name	A meaningful name for the measurement.
string	mod18.settings	Modbus 18 Settings	Settings for Modbus Channel 18. Refer to user guide.
string	mod18.cal	Modbus 18 Calibration	Calibration paramters for Modbus Channel 18. Refer to user guide.
string	mod18.unit	Modbus 18 Unit	The unit of measure associated with the calibration.
string	mod18.warning	Warning	Warning thresholds. Refer to user guide.
string	mod18.alarm	Alarm	Alarm thresholds. Refer to user guide.
string	mod19.name	Modbus 19 Name	A meaningful name for the measurement.
string	mod19.settings	Modbus 19 Settings	Settings for Modbus Channel 19. Refer to user guide.
string	mod19.cal	Modbus 19 Calibration	Calibration paramters for Modbus Channel 19. Refer to user guide.
string	mod19.unit	Modbus 19 Unit	The unit of measure associated with the calibration.
string	mod19.warning	Warning	Warning thresholds. Refer to user guide.
string	mod19.alarm	Alarm	Alarm thresholds. Refer to user guide.
string	mod20.name	Modbus 20 Name	A meaningful name for the measurement.
string	mod20.settings	Modbus 20 Settings	Settings for Modbus Channel 120. Refer to user guide.
string	mod20.cal	Modbus 20 Calibration	Calibration paramters for Modbus Channel 120. Refer to user guide.
string	mod20.unit	Modbus 20 Unit	The unit of measure associated with the calibration.
string	mod20.warning	Warning	Warning thresholds. Refer to user guide.
string	mod20.alarm	Alarm	Alarm thresholds. Refer to user guide.
boolean	endpoint.config_to_portal	Configuration via Senquip Portal	Enables connection to Senquip Portal for remote configuration.
boolean	endpoint.data_to_portal	Send Data to Senquip Portal	Enables data from the device to be sent to the Senquip Portal.
boolean	endpoint.buffer_enable	Offline Buffer	Save data if device is offline, and send when network is available.
boolean	endpoint.addtimedate	Add Formatted Time	This option adds a human readable time/date format to the data output.
boolean	endpoint.network_report	Report Network Info	Add network details and signal strength to data output.
boolean	endpoint.sq_data_format	Use Senquip Data Format	Automatically send the Senquip data message to the endpoints below (does not affect data to Senquip Portal). If unchecked, no data is sent and the device script should create messages.
boolean	endpoint.udp.enable	UDP	Enables sending data over UDP to specified address below.
string	endpoint.udp.address	UDP Address	Address and port to send data to.
boolean	endpoint.http.enable	HTTP POST	Enables sending data via a HTTP POST request to address below.
string	endpoint.http.address	HTTP Address	Destination address and port for HTTP POST request.
boolean	endpoint.mqtt.enable	MQTT	Enables sending data to a MQTT broker.
string	endpoint.mqtt.server	Broker Address	MQTT Broker Address and Port.
string	endpoint.mqtt.client_id	Client ID	Client ID to send to the broker. Defaults to device.id if left blank.
string	endpoint.mqtt.data_topic	Data Topic	Topic for Senquip formatted data messages. A single ‘?’ character will be replaced with the Device ID. Leave blank for ‘?/data’.
string	endpoint.mqtt.user	Username	Username for MQTT authentication with username/password. (Optional)
string	endpoint.mqtt.pass	Password	Password for MQTT authentication with username/password. (Optional)