Glossary

Terms used in this guide, in alphabetical order.

1-Wire

A single-wire serial bus used by low-cost sensors such as digital temperature probes. Supported on selected IO terminals.

3G & 4G

Generations of cellular network technology. 4G LTE is the current mainstream standard; 3G networks have been switched off in many countries. Senquip devices use 4G LTE, including the low-power LTE-M1 variant.

4-20 mA

An industrial sensor signal in which the measured value is represented by a current between 4 mA and 20 mA. Because 0 mA is outside the range, a broken wire can be detected.

Alert

An event raised when a measurement crosses a threshold you set. Each alert has an Alert Type, a low threshold, a high threshold and a Hysteresis. See Warnings and Alarms.

Alert Type

The category of an alert: Disabled, Info, Alert, Warning or Alarm. It decides how the event is shown on the Senquip Portal and whether it is forwarded by email or SMS. On the ORB-X1, warnings and alarms are set separately instead.

ASCII

American Standard Code for Information Interchange. The most common code used by computers to represent text (letters, numbers and symbols) so that it can be sent between devices.

Base Interval

The time between the device waking to check which measurements are due and whether a transmission is scheduled. Measurement and transmit intervals are set as multiples of the Base Interval.

Basic plan

The plan included with every Senquip device for the life of the product. It allows device management, firmware updates, script writing, and viewing of current data at up to 5 minute updates. See also Hosted plan.

Batch Transmit

A setting that stores every measurement taken at the Base Interval and sends them together at the Transmit Interval, to save power.

CAN

Controller Area Network. A robust two-wire bus used by vehicles and machines to share data between controllers. J1939 is a common CAN protocol on heavy vehicles and engines.

certificate-authority

A certificate authority (CA) is a trusted organisation that issues the digital certificates used to prove a server’s identity. An HTTPS or MQTTS endpoint may need the CA certificate of the destination loaded onto the device.

Command Queue

The list of settings changes, firmware updates and other commands waiting on the Senquip Portal to be sent to a device. Commands are sent the next time the device connects.

Data Source

A measurement reported by a device and available to widgets, charts and dashboards. Each has a name and a short key, shown in square brackets, such as [cp13].

Device ID

The unique nine-character identifier of a Senquip device. It is printed on the device label and the Device Credentials card, and is used to add the device to the Senquip Portal.

Endpoint

A destination for device data: the Senquip Portal, or your own server using UDP, HTTP(S) or MQTT(S).

Exception

An informational message, alert, warning or alarm reported by a device in its data message. See Exceptions.

Exception Interval

The transmit rate used while a warning or alarm is active, so that an active event is reported more often than normal data.

Firmware family

The firmware a product runs: SFW001 for the ORB-X1, SFW002 for the ORB-C1 and QUAD-C2, SFW004 for the ORB-C3 and QUAD-C3, and SFW005 for the UNI-Z1. Firmware numbers start with the family code.

Freight Mode

A shipping state in which all transmitters are off and battery drain is reduced to almost zero. The only way to bring a device out of Freight Mode is to apply power to it.

Group

A collection of devices on the Senquip Portal. Groups set user permissions for many devices at once, apply settings in bulk and share dashboards.

Hibernate

A low-power state entered when external power is lost, if Hibernate on Power Loss is turned on. The device wakes and transmits at the Hibernate Period and runs normally again when power returns.

Hosted plan

A paid plan that adds data storage and visualisation on the Senquip Portal, including historical data, charts, dashboards, email and SMS alerts, and faster updates. See also Basic plan.

Hysteresis

A margin around a threshold that stops an alert switching on and off repeatedly when a value hovers near it. An alert starts at the threshold plus hysteresis and clears at the threshold minus hysteresis.

JSON

JavaScript Object Notation (JSON) is a text-based format for structured data. Senquip devices send their data, and the Senquip Portal stores settings, in JSON.

jubilee-clips

A jubilee clip, also known as a hose clamp, is used with the supplied brackets when pole mounting an ORB.

LiPo

Lithium-ion polymer. The rechargeable battery chemistry used in the ORB-C1 and QUAD-C2.

LTE-M1

LTE Cat M1 is a low-power cellular technology for IoT devices with modest data needs. Compared with standard 4G LTE, it uses less power and gives better reach inside buildings.

LTO

Lithium titanate. The rechargeable battery chemistry used in the ORB-C3, QUAD-C3 and UNI-Z1, chosen for its long cycle life and wide temperature range.

Metric

In Vision dashboards, the way a value is worked out from one measurement over a period, such as Latest, Average, Total, Difference or Accumulation.

MFA

Multi-factor authentication. An extra sign-in step that asks for a code from an authenticator app as well as your password. Set up from the Account page.

MODBUS

Modbus RTU is an open serial protocol, carried over RS-232 or RS-485, in which one controller polls many devices for register values. It is widely used in industrial automation.

MQTT

Message Queuing Telemetry Transport. A lightweight publish-subscribe protocol for sending messages between devices and servers. MQTTS is MQTT secured with TLS.

NIST

The National Institute of Standards and Technology, a United States agency that publishes measurement and security standards.

Pre-charge

The slow initial charge a deeply discharged battery receives before normal charging. The device does not start until the battery reaches a minimum safe level.

RS-232 and RS-485

Serial interface standards. RS-232 connects one device to another over short distances; RS-485 uses a differential pair to connect many devices over long cables.

Script

A program written in mJS, a restricted form of JavaScript, that runs on the device to add custom measurements, settings, calculations and control.

SDI-12

A serial protocol used by environmental sensors such as soil moisture and weather sensors. Supported on selected IO terminals.

Senquip Connect

The Senquip mobile app for setting up a device over Bluetooth while it is in Setup Mode.

Senquip Portal

The Senquip web application for managing devices, viewing data and configuring alerts, at portal.senquip.com.

Setup Mode

A temporary mode, entered with the Setup button, in which a device can be configured locally with the Senquip Connect app or its web server.

Setup password

The password printed on the Device Credentials card. It is needed to configure a device locally and to add it to a Senquip Portal account, so keep it secure.

SSO

Single sign-on. Signing in to the Senquip Portal with an existing work account, such as Microsoft Entra ID, when your organisation has set it up.

Transmit Interval

The number of Base Intervals between transmissions of data.

Trigger

A button on the device page that sends a command to a device, to be handled by its script. Triggers can be queued or discarded when the device is offline.

Vision Dashboard

A Senquip Portal page that summarises the devices in a group as tables, charts, headline figures and a map, using one or more saved views.

Web server

A local web page served by the device, used for setup when connected to its Wi-Fi access point.

Widget

A card on the device page that shows data. The Widget Editor creates custom graphical widgets; the Chart Editor creates custom charts.